Lincoln Impinger X2 Ovens with Push Button Controls 3240-2 Bedienungsanleitung

X2svcmanual REV: 1/8/07 SERVICE MANUAL (DOMESTIC & INTERNATIONAL) IMPINGER X2 OVENS WITH ANALOG CONTROLS MODEL 3240-2, 3262-2, 3270-2

Impinger X2 – Analog Service Manual – Dom & Int’l 10 assembly. Check for damaged or torn belting. Check conveyor shaft bearings for damage or exce

Impinger X2 – Analog Service Manual – Dom & Int’l 11 TROUBLESHOOTING GUIDE 3240-2* 230VAC 50 HZ. 1 PHASE 3262-2* 230VAC 50 HZ. 1

Impinger X2 – Analog Service Manual – Dom & Int’l 12 Oven will not heat Gas supply Check for adequate gas supply to oven. Manual gas shut off

Impinger X2 – Analog Service Manual – Dom & Int’l 13 Burner control Check for supply voltage at terminal #7 on burner control. If no voltage is

Impinger X2 – Analog Service Manual – Dom & Int’l 14 On at this time Electronic temperature control control at terminals #13 and #12. Of there is

Impinger X2 – Analog Service Manual – Dom & Int’l 15 switch as needed. Control, conveyor Check for supply voltage to conveyor control at termin

Impinger X2 – Analog Service Manual – Dom & Int’l 16 REMOVAL, INSTALLATION & ADJUSTMENTS IMPINGER X2 SERIES OVENS CAUTION! BEFORE REMOVING

Impinger X2 – Analog Service Manual – Dom & Int’l 17 9. Remove burner tube bracket and Burner tube. To remove burner tube, Remove cap from idl

Impinger X2 – Analog Service Manual – Dom & Int’l 18 RELAY, MAIN FAN, - REPLACEMENT 1. Shut off power at main breaker. 2. Remove control box co

Impinger X2 – Analog Service Manual – Dom & Int’l 19 4. Disconnect wiring from burner blower relay and mark all wiring for reassembly. 5. Remove

Impinger X2 – Analog Service Manual – Dom & Int’l 2 SEQUENCE OF OPERATION IMPINGER X2 OVENS 3240-2* 120/230VAC 60 HZ. 1 PHASE 3240-2* 1

Impinger X2 – Analog Service Manual – Dom & Int’l 20 7. Press the “FUNC” key until the display reads “Cnf”. Shut off burner, remove control from

Impinger X2 – Analog Service Manual – Dom & Int’l 21 4. Disconnect all wiring from the temperature regulation valve and the main gas valve. Mark

Impinger X2 – Analog Service Manual – Dom & Int’l 22 HALL EFFECT SENSOR – REPLACEMENT 1. Shut off power at main breaker. 2. Remove control box

Impinger X2 – Analog Service Manual – Dom & Int’l 23 CONVEYOR CONTROL – PROGRAMMING 1. Determine which brand of motor is connected to the convey

Impinger X2 – Analog Service Manual – Dom & Int’l 24 CONVEYOR CONTROL – PROGRAMMING – DAYTON MOTOR, DIRECT DRIVE Jumper “DAR

Impinger X2 – Analog Service Manual – Dom & Int’l 25 CONVEYOR CONTROL – PROGRAMMING – DAYTON MOTOR, RIGHT ANGLE DRIVE Jumper “

Impinger X2 – Analog Service Manual – Dom & Int’l 26 CONVEYOR CONTROL – PROGRAMMING – GLEASON AVERY MOTOR, DIRECT DRIVE Jumper

Impinger X2 – Analog Service Manual – Dom & Int’l 27 This page intentionally left blank.

Impinger X2 – Analog Service Manual – Dom & Int’l 28 IMPINGER X2 OVENS GENERAL VIEW LETTER PART NUMBER DESCRIPTION A 9004415 Finger housing,

Impinger X2 – Analog Service Manual – Dom & Int’l 29

Impinger X2 – Analog Service Manual – Dom & Int’l 3 SEQUENCE OF OPERATION IMPINGER X2 OVENS 3240-2* 230VAC 50 HZ. 1 PHASE 3262-2* 230VA

Impinger X2 – Analog Service Manual – Dom & Int’l 30 IMPINGER X2 OVENS OVEN CAVITY LETTER PART NUMBER DESCRIPTION A 9004435 Guard, shaft – 3

Impinger X2 – Analog Service Manual – Dom & Int’l 31

Impinger X2 – Analog Service Manual – Dom & Int’l 32 IMPINGER X2 OVENS CONTROL BOX LETTER PART NUMBER DESCRIPTION A 508120EP Coupling w/slee

Impinger X2 – Analog Service Manual – Dom & Int’l 33

Impinger X2 – Analog Service Manual – Dom & Int’l 34 IMPINGER X2 OVENS BURNER/DRIVE END LETTER PART NUMBER DESCRIPTION A 7007124 Flange, bur

Impinger X2 – Analog Service Manual – Dom & Int’l 35

Impinger X2 – Analog Service Manual – Dom & Int’l 36 IMPINGER X2 OVENS CONVEYOR, SINGLE LETTER PART NUMBER DESCRIPTION A 100403103 Shelf, in

Impinger X2 – Analog Service Manual – Dom & Int’l 37

Impinger X2 – Analog Service Manual – Dom & Int’l 38 IMPINGER X2 OVENS CONVEYOR, DUAL BELT LETTER PART NUMBER DESCRIPTION A 100403103 Take o

Impinger X2 – Analog Service Manual – Dom & Int’l 39

Impinger X2 – Analog Service Manual – Dom & Int’l 4 SCHEMATIC DIAGRAM MODEL 3240-2, 3262-2, 3270-2 60 HZ.

Impinger X2 – Analog Service Manual – Dom & Int’l 40

Impinger X2 – Analog Service Manual – Dom & Int’l 5 SCHEMATIC DIAGRAM MODEL 3240-2, 3262-2, 3270-2 50 HZ.

Impinger X2 – Analog Service Manual – Dom & Int’l 6 TROUBLESHOOTING GUIDE 3240-2* 120/230VAC 60 HZ. 1 PHASE 3240-2* 120/230VAC 60 HZ

Impinger X2 – Analog Service Manual – Dom & Int’l 7 bearings. Replace bearings as needed. Oven will not heat Gas supply Check for adequate gas s

Impinger X2 – Analog Service Manual – Dom & Int’l 8 wiring back to the centrifugal switch of the burner blower motor. If voltage is present, check

Impinger X2 – Analog Service Manual – Dom & Int’l 9 Temperature regulation valve If 120VAC is present on the electronic temperature control, te